You will need a printer with a bed that can print 220mm on X or Y axis.
I use Prusaslicer. If you use something else, you will need to adapt your settings.
Check my general print settings here
In the table bellow you will find my printing settings for each part.
Print Profile list my settings for each part providing the layer height, the infill and the number of perimeter. For example .2mm 20% 2p means
- .2mm = Layer Height
- 20% = infill
- 2p = numbers of perimeter
Filament Type is the type of filament you should use for that given part. Here is the legend used in that column
- 85A – TPU with a Shore Hardness of 85A – Recommended Ninjatek NinjaFlex. This is for the tires and TPU front bumpers.
- 70D – TPU with a Shore Hardness of 70D – Recommended Ninjatek Armadillo. This is tough TPU for the wheels.
- YC – Your Choice. There are plenty of filaments type out there that you may choose to print the body and chassis whether it’s PLA, PETG, ABS, PC and so on. Use what you feel will give the best results with your setup. Some filament type require special equipment, ventilation and so on. Use what you are comfortable with.
Grams Needed is the total filament required in grams to print that part.
Time is as you guessed it the time my slicer thinks it will take
Support is the support configuration I use
Orientation. I provide the files in what I believe is the best printing orientation. Feel free to experiment better ways to print these parts. Feel free to share your settings in our Facebook group.
Print Settings:
- For 85A and 70D TPU: Print slowly. Max speed 25mm/s. I use Elmer glue stick on my PEI BED. You can also use 3D LAC. Check the recommended Nozzle and Bed temperature from the filament manufacturer.
I’m using more and more a 0.6mm nozzle. It prints faster. In this document I’m using a 0.4mm for reference.
Part | Profile | Filament Type | Grams Needed | Time | Support |
---|---|---|---|---|---|
_Printer calibration 5-10-4 | .2mm 20% 2p | YC | 1.25 | 0:10 | None |
2x Front Wheel | .2mm 50% 3p | 70D | 39.38 | 8:04 | Build Plate Only |
2x Mirror | .2mm 20% 2p | YC | 1.08 | 0:08 | None |
2x Rear Wheel | .2mm 50% 3p | 70D | 51.72 | 10:34 | Build Plate Only |
4x Drive spigot 6mm | .2mm 50% 3p | 70D | 2.67 | 0:34 | None |
4x Super sport Tire | .2mm 25% 3p | 157.84 | 85A | 1:58 | None |
4x Super Sport Wheel | .2mm 50% 3p | 70D | 50.79 | 31:00 | Support Enforcer. Paint on Support on inside rim only. |
Battery Clip | .2mm 20% 2p | YC | 7.03 | 1:07 | Build plate only |
Body Back | .2mm 20% 2p | YC | 117.59 | 11:28 | Build plate only |
Body Driver | .2mm 20% 2p | YC | 15.91 | 2:12 | Everywhere |
Body Front | .2mm 50% 3p | YC | 47.04 | 4:48 | Build plate only |
Body Hood | .2mm 50% 3p | YC | 110.49 | 11:56 | Everywhere |
Dashboard | .2mm 20% 2p | YC | 2.38 | 0:14 | None |
Drive shaft | .2mm 70% 5p | YC | 12.51 | 1:22 | Build plate only |
Driver | .2mm 20% 2p | YC | 93.38 | 10:51 | Everywhere. Take your time to remove the support. |
Ferrari Exhaust Left | .2mm 20% 2p | YC | 8.58 | 1:12 | None |
Ferrari Exhaust Right | .2mm 20% 2p | YC | 8.63 | 1:12 | None |
Ferrari TPU Grill | .2mm 25% 3p | 85A | 27.14 | 5:14 | Build Plate Only |
Frame front | .2mm 50% 3p | YC | 87.73 | 9:08 | Build Plate Only |
Frame One Part | .2mm 50% 3p | YC | ? | ? | My printer is not big enough I don’t have the info |
Frame rear | .2mm 50% 3p | YC | 201.86 | 19:34 | Build Plate Only |
Gas Cap | .2mm 20% 2p | YC | 1.49 | 0:11 | Build plate only |
Rear Gear Cover | .2mm 20% 2p | YC | 13.46 | 1:48 | Build plate only |
Suspension Lower bracket Front | .2mm 50% 3p | YC | 4.93 | 0:33 | Build plate only |
Suspension Lower bracket Rear | .2mm 50% 3p | YC | 7.78 | 0:53 | Build plate only |
Suspension Upper bracket Front | .2mm 50% 3p | YC | 10.47 | 1:20 | Build plate only |
Suspension Upper bracket Rear | .2mm 50% 3p | YC | 15.75 | 1:57 | Build plate only |
Tire Front Left | .2mm 25% 3p | 85A | 34.68 | 7:07 | Support Enforcer. Paint on Support on inside rim only. |
Tire Front Right | .2mm 25% 3p | 85A | 34.68 | 7:07 | Support Enforcer. Paint on Support on inside rim only. |
Tire Rear Left | .2mm 25% 3p | 85A | 39.09 | 7:42 | Support Enforcer. Paint on Support on inside rim only. |
Tire Rear Right | .2mm 25% 3p | 85A | 39.09 | 7:42 | Support Enforcer. Paint on Support on inside rim only. |
Vanwall exhaust left | .2mm 20% 2p | YC | 2.13 | 0:17 | None |
Vanwall exhaust Right | .2mm 20% 2p | YC | 2.13 | 0:17 | None |
Vanwall pipes left | .2mm 20% 2p | YC | 1.63 | 0:17 | None |
Vanwall pipes right | .2mm 20% 2p | YC | 1.63 | 0:17 | None |
Vanwall TPU Front | .2mm 25% 3p | 85A | 28.59 | 5:24 | Build plate only |
Vanwall windshield | .2mm 20% 2p | YC | 5.23 | 0:48 | Build plate. You can add a color change at 11mm height for the glass |
Vertical Servo Mount | .2mm 50% 3p | YC | 20.44 | 2:30 | None |